Upper  guide bracket kit

 Includes 2 set screws and upper guide bracket. Original equipment on Delta/Rockwell saws with 14" wheels. This set will also fit most imported (non Delta or Rockwell) brands. (AMT, Reliant, Buffalo)

Complete upper sliding  wheel bracket with hinge assembly, wheel axle, tension knob and tension spring.  

426 02 359 0005

Delta Replacement upper wheel sliding bracket casting only (includes tracking adjustment screw)   

(may also fit  imported 14" Band saws also*)   

Click here for more views 

Delta/Rockwell  Upper Wheel Support Hinge Kit

(May also fit AMT, Buffalo, Reliant and other imported 14" band saws*. ) Use with  above sliding bracket.

Replacement Tires for 14" Band Saws

If you have the original black rubber tires on your saw, it's time to replace them with the new urethane ones. You will have improved tracking and less slippage. Requires two.

  For AMT,Buffalo,Reliant or other Imported Band Saws, Use:

Urethane tire for 14" Band Saw

  14" Replacement Upper Wheel Assembly, includes Tire. Upper wheel also include bearings. Balanced for smooth operation...

Replacement guide bearings, for upper &  lower blade guides

426-05-380-5001

Replacement Bearing Only:

 -Larger, older style than above. Was used  on a hexed shaft (shaft no longer available)

Table insert for 20" band saw( not shown)

Replacement upper wheel bearings:

12" and 24" Ripfence, Mounts to table, includes  mounting hardware

Replacement Table Kit

Larger 16" X 16" for more support. Fits Delta/Rockwell 14" Band Saws

Includes insert, pin,& mounting screws.

Lower Wheel Replacement Shaft and Bearing Kit:

Includes shaft, bearings, spacers, nuts and key for replacement on most 14" American made Delta/Rockwell wood cutting band saws. For Dimensions of the shaft and bearings, click HERE

Knob Replacement Kit for 14" Bandsaws

Replace older, obsolete round table hold-down knobs with the new style, updated levers. Includes 2 new toggle bolts, stop nuts & levers for front and rear of table

(will not fit AMT/Buffalo)

Height Attachment

Increases capacity under guides to 12" includes new guide posts & guarding

Replacement Manual push-button switch     

For Single phase, manual start only 115-230V.

(does not work on low voltage controls)

 Replaces obsolete Furnas  12BAT.

Includes new push-button plate. Used on newer Delta & X5 machines.

Replacement bearing set for Carter Roller Guides  (10 per set)

Table Trunnions

    Set of Front and Rear table trunnions. (Does not include scale plate.)

These will fit all Delta/Rockwell 14" saws and many imports ( AMT, Buffalo, Reliant*)

(*fit guaranteed only on American made Delta/Rockwell)

(For Dimensions, click HERE)

Degree scale plate for above. Stick-on

Installs in above trunnions. Use two per saw.

Complete  lower blade guide assembly with bearings and guide blocks installed. For 14" Delta/Rockwell saws only.

426-02-014-0006

For 14" Delta/Rockwell saws only

Delta 25-870 Magnetic Work Light

• Provides the added light needed for improved accuracy in the work shop
• Magnetic base mounts securely to any ferrous surface
• 6-ft cord offers more reach and versatility
• 14-in flexible arm allows you to direct the light right where you need it
• Uses a standard 40 watt bulb (not included)

Click here to see the assembled lower table bracket and guide assembly...

Blade Guard

(Mounts to  the left side of the band saw)

  (for newer saws with hinged blade doors only)

Used in Delta/Rockwell 14" wood/Metal cutting band saws. Set of two belts. For models 28-300, 28-303, 28-306 & 28-380.

Band saw Mobile Bases- inside dimensions shown